Log the controllers of Home Automation Ethernet controllers ethernetroommanager, ethernetheatmanager, ethernetsolarmanager @ Home Automation eHouse.Pro
Home Automation eHouse Ethernet version. Connectors of Ethernet controllers description refers to average Ethernet controllers: ethernetroommanager ethernetheatmanager ethernetsolarmanager other dedicated Ethernet controllers based on the same PCB description is not for large controllers mr fix it CommManager LevelManager most eHouse controllers connectors are double row IDC with different amounts of pins, for easy installation and quick connection, and to provide for easy installation through the use of tapes - mounted flat with klentsht IDC connectors on the ends (especially Crimp Connector ID). Assembly and disassembly wiring does not require Forging grooves in the walls due to the thickness of the strip is about 1 mm flat.
NEW! ; Totally do not need a screwdriver to connect the wires to the large number of contacts and the Controller clamping flat cable regardless of the number of cores it takes several mr fix it seconds. This facilitates the removal and control service and diagnostic for the detection mr fix it of problems in the case of the installation error. Ethernet leads Intelligent Ethernet controllers home eHouse ethernetroommanager, ethernetheatmanager, ethernetsolarmanager Pin no. 1. Field is marked with a square solder on the PCB and the housing Additionally arrow slot. After the first pin is located in the middle of the housing cut - out slot, prevent reverse insertion of the plug to turn. Pins are numbered in sequence with priority columns: ____________________________________________________________ | 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 | 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 | ^ _______________________________________________________ ADC inputs - analogue inputs - Digital Measurement (ADC inputs) (0, 3 W3) relative weights - Do not connect any external voltage (IDC - 20)
1 - GND / Ground (0 W) 2 - GND / Ground (0 W) 3 - ADC in 2 4 - ADC in 10 5 - ADC in 3 6 - ADC in 11/12 * Digital Input 7 - ADC in 4 8 - ADC in 12/11 * Digital mr fix it Input 9 - ADC in 5 10 - ADC in 13/10 * Digital input 11 - ADC in 6 12 - ADC in 14/9 * Digital input 13 - ADC at 7 14 - ADC in 15 / digital input 8 * 15 - ADC in 8 (optional temperature sensor mounted on the module or panel outside erm) 16 - ADC in 0 17 - ADC in 9 (optionally mounted light sensor (fototransistor +) on the module or panel outer erm) 18 - ADC in 1 19 - Wed (+3 V3) - requires a jumper to power the erm limiting current / temperature sensors for power (resistor 100 about) 20 - Wed (+3 V3) * Compact digital inputs do not connect digital inputs - Digital Input (On / Off) short to ground or open (do not connect any voltage zevn ä kznitsh) (IDC - 14) 1 - GND / Ground (0 W) 2 - GND / Ground (0 W) 3 - Digital Input 1 4 - Digital Input 2 5 - Digital Input 3 6 - Digital Input 4 7 - Digital Input 5 8 - Digital Input 6 9 - Digital Input 7 10 - Digital Input 8 * 11 - Digital Input 9 * 12 - Digital Input 10 * 13 - Digital Input 11 * 14 - Digital Input 12 ** compact analog mr fix it inputs digital outputs - with controllers digital outputs for direct connection to the relay coil control relay (IDC - 40 or IDC - 50)
1 - vkkdrv mr fix it - against - surge for the relay connected to the relay coil 12V (diode to vkk) 2 - vkkdrv - against - surge for the relay connected to the relay coil 12V (diode to vkk) 3 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 1 4 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 2 5 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 3 6 - Digital mr fix it output for direct connection to the relay coil (12V / 20 mA) no. 4 7 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 5 8 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 6 9 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 7 10 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 8 11 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 9 12 - Digital mr fix it R
Home Automation eHouse Ethernet version. Connectors of Ethernet controllers description refers to average Ethernet controllers: ethernetroommanager ethernetheatmanager ethernetsolarmanager other dedicated Ethernet controllers based on the same PCB description is not for large controllers mr fix it CommManager LevelManager most eHouse controllers connectors are double row IDC with different amounts of pins, for easy installation and quick connection, and to provide for easy installation through the use of tapes - mounted flat with klentsht IDC connectors on the ends (especially Crimp Connector ID). Assembly and disassembly wiring does not require Forging grooves in the walls due to the thickness of the strip is about 1 mm flat.
NEW! ; Totally do not need a screwdriver to connect the wires to the large number of contacts and the Controller clamping flat cable regardless of the number of cores it takes several mr fix it seconds. This facilitates the removal and control service and diagnostic for the detection mr fix it of problems in the case of the installation error. Ethernet leads Intelligent Ethernet controllers home eHouse ethernetroommanager, ethernetheatmanager, ethernetsolarmanager Pin no. 1. Field is marked with a square solder on the PCB and the housing Additionally arrow slot. After the first pin is located in the middle of the housing cut - out slot, prevent reverse insertion of the plug to turn. Pins are numbered in sequence with priority columns: ____________________________________________________________ | 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 | 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 | ^ _______________________________________________________ ADC inputs - analogue inputs - Digital Measurement (ADC inputs) (0, 3 W3) relative weights - Do not connect any external voltage (IDC - 20)
1 - GND / Ground (0 W) 2 - GND / Ground (0 W) 3 - ADC in 2 4 - ADC in 10 5 - ADC in 3 6 - ADC in 11/12 * Digital Input 7 - ADC in 4 8 - ADC in 12/11 * Digital mr fix it Input 9 - ADC in 5 10 - ADC in 13/10 * Digital input 11 - ADC in 6 12 - ADC in 14/9 * Digital input 13 - ADC at 7 14 - ADC in 15 / digital input 8 * 15 - ADC in 8 (optional temperature sensor mounted on the module or panel outside erm) 16 - ADC in 0 17 - ADC in 9 (optionally mounted light sensor (fototransistor +) on the module or panel outer erm) 18 - ADC in 1 19 - Wed (+3 V3) - requires a jumper to power the erm limiting current / temperature sensors for power (resistor 100 about) 20 - Wed (+3 V3) * Compact digital inputs do not connect digital inputs - Digital Input (On / Off) short to ground or open (do not connect any voltage zevn ä kznitsh) (IDC - 14) 1 - GND / Ground (0 W) 2 - GND / Ground (0 W) 3 - Digital Input 1 4 - Digital Input 2 5 - Digital Input 3 6 - Digital Input 4 7 - Digital Input 5 8 - Digital Input 6 9 - Digital Input 7 10 - Digital Input 8 * 11 - Digital Input 9 * 12 - Digital Input 10 * 13 - Digital Input 11 * 14 - Digital Input 12 ** compact analog mr fix it inputs digital outputs - with controllers digital outputs for direct connection to the relay coil control relay (IDC - 40 or IDC - 50)
1 - vkkdrv mr fix it - against - surge for the relay connected to the relay coil 12V (diode to vkk) 2 - vkkdrv - against - surge for the relay connected to the relay coil 12V (diode to vkk) 3 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 1 4 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 2 5 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 3 6 - Digital mr fix it output for direct connection to the relay coil (12V / 20 mA) no. 4 7 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 5 8 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 6 9 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 7 10 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 8 11 - Digital output for direct connection to the relay coil (12V / 20 mA) no. 9 12 - Digital mr fix it R
No comments:
Post a Comment